My Key to Organizing Small Allen Wrenches

If you're like me, you have an unorganized bin of loose Allen wrenches in your workshop.

If you’re like me, you have an unorganized bin of loose Allen wrenches in your workshop. SAE and metric sizes coexist is this microcosm without discrimination or prejudice. Maybe you call these tools hex keys. Whatever the case, they are a blessing and a curse. In larger sizes (bigger than 3/16″ or 4.5mm), they are cheap, convenient, and robust tools. The smaller Allen wrenches, however, present several problems for me.

First of all, the wrenches and the heads of the fasteners that they drive tend to strip easily. This is exaggerated by the fact that there are many different sizes which are indiscernible by eye. Selecting the correct wrench for an application can be challenging. Oh, did I mention that these wrenches are not even marked with their size?

Despite their challenges, small Allen wrenches are a fact of life in the RC world. They are used in many, many applications across the RC spectrum. In fact, most of the smaller hex keys in my bin were included with RC products. Many of the larger tools can be traced to Ikea.

Small Allen wrenches can be frustrating to use. So I came up with a simple system to manage these tools. Small Allen wrenches can be frustrating to use. So I came up with a simple system to manage these tools.

I have a somewhat masochistic MO when I need to find a small Allen wrench. I reach into that disheveled bin and pull out a handful of tools that look to be about the right size. Then I go through the frustrating exercise of test fitting each wrench in the fastener until I find a good fit. If I’m lucky, I’ll score a good wrench within the first five tries.

After years of this inefficient approach, I finally decided to end the madness. I set out to find a simple means of organizing my small Allen wrenches. I decided that my system would have to be easy to understand, easy to implement, and easy to maintain.

The Allen Parsing Project

Before I get into my organizational method, I should point out that I am fully aware of Allen wrench sets that come in cases with each of the wrench sizes marked. I have several of them. They are definitely an improvement over the “toss it in the bin” approach, but they still demand a simple method of identification when the wrenches are being used. It’s easy to put a wrench back in the incorrect slot. Then the size markings on the case become useless.

My first step in addressing the problem was to determine what I was dealing with. I really had no idea how many different wrench sizes were in my bin, or how many were duplicates. So I dumped the bin on my workbench and measured each Allen wrench with a set of digital calipers. I took at least three measurements of each wrench.

I used calipers to determine the exact size of each of my Allen wrenches. I used calipers to determine the exact size of each of my Allen wrenches.

My budget calipers only measure to a precision of .1mm. But really, if I thought I was going to have to differentiate tools with differences less than that, I doubt I would have bothered. Not knowing whether any of the wrenches were SAE or metric, I measured and recorded in both units. But it was easiest to sort the wrenches by their metric values. Don’t let that go to your head you metric justice warriors (you know who you are).

I grouped the wrenches according to size. I grouped the wrenches according to size.

When I was done measuring, I had 11 piles of wrenches ranging in size from 1.1mm to 3.9mm. My next step was to inspect every wrench for wear (rounded edges). The reason I did this after measuring, rather than before, was to ensure that I didn’t discard any lone examples of a given size. I figured that I could salvage any such wrenches by removing the worn tips with my bench grinder. As it turned out, I had enough samples in each size that I was able to toss all of the worn tools. I’m ashamed to say that there were several.

I tossed out any wrenches that showed signs of wear. I tossed out any wrenches that showed signs of wear.

Contrast out of Chaos

I contemplated several potential methods of marking the Allen wrenches so that I could instantly know what size any given wrench is. Applying heatshrink tubing would have been great, but I didn’t have a sufficient variety of colors in tubing small enough to stay snug on the wrenches.

I decided to go with paint. I was digging up the colors I would need from my paint stash when I remembered my daughters’ bucket of nail polish. Tons of colors and built-in brushes too! I quickly figured out that I didn’t require 11 different colors. I really only needed to be able to differentiate small differences in sizes. So, I could repeat colors on sizes that are easily distinguished (ex. I painted the 1.4mm and 2.9mm wrenches orange).

Bright fingernail polish was used to denote the size of every tool. This makes it easy to visually differentiate similarly-sized wrenches. Bright fingernail polish was used to denote the size of every tool. This makes it easy to visually differentiate similarly-sized wrenches.

I picked a handful of colors that contrasted well on the wrenches. Some of the wrenches are black and others are nickel. Bright fluorescent color seem to work best. I should probably pick up a set of fluorescent nail polish to keep in my shop just for this purpose. The girls are bound to want their bucket back sooner or later!

I painted two stripes on each wrench to make the colors easily visible. I stabbed the tools into scrap foam to keep them upright while the polish dried. I also applied a drop of each color to the corresponding measurements on my size chart. I’ll keep this reference in my tool box. As I obtain more wrenches (I already have), I’ll measure them, paint them the correct color, and toss them in the bin.

I’ve had cause to use small Allen wrenches a few times since implementing this system. It is extremely rare for any RC-related instruction manual to indicate the necessary size of a wrench for a given Allen-head screw. So finding the correct tool still involves some trial and error. What has improved is that I no longer test duplicates of the wrong size. I grab one example of each candidate and begin test fitting. It also helps that I culled the worn out tools. The process is now a little faster and much less frustrating.

The process of finding the correct wrench is now quicker and less frustrating. The process of finding the correct wrench is now quicker and less frustrating.

The unknown factor moving forward is the durability of the nail polish on the wrenches. I don’t expect any major issues there, but I’ll definitely be making sure it doesn’t chip off too easily. I’ll also need to make sure that I do not get lazy and start adding unmarked wrenches to the bin. I suspect that I’ll keep a side stash of new wrenches and process them for the bin on rainy days.

This little project took me less than an hour from start to finish. I should have invested this time many years ago. Now, I need to apply the same thought process to my drawers full of unsorted model airplane propellers.

Do you have a handy method for organizing Allen wrenches? Tell me about it!

Terry is a freelance writer living in Buffalo, NY. Visit his website at TerryDunn.org and follow him on Twitter and Facebook. You can also hear Terry talk about RC hobbies as one of the hosts of the RC Roundtable podcast.

Comments (17)

17 thoughts on “My Key to Organizing Small Allen Wrenches

  1. Racing RC cars for 30 years makes me recoil in horror everytime I see someone using “L”-shape allen keys 🙂 You have created a nifty method to organise though, which I’ll apply to the unruly pile of non-RC allen keys lurking in my tool box

    I found it more effective (no more stripped Allen heads) and efficient ( just one set of tools) to buy a dedicated set of Allen drivers. They are more expensive than L keys, but the investment in quality tools is worth far more than the savings on cheaper ones.

  2. i don’t need to let it go to my head when it’s already there, right? asking for a friend. (and trying very hard not to tell you ‘told you so.’ ;))

  3. Your pile of wrenches looks similar to mine. Maybe it’s time I weed through my collection. I probably have 5-6 wrenches of the same size that I can sort down to the best two.

    I like the paint idea but I use small strips of colored shrink tubing on mine. Doesn’t rub off like paint might. But, to be honest, I didn’t do that to ALL my Allen wrenches, just the ones that I seem to use most often on my models.

    Fun article. What are we organizing next?? 😉

  4. Awesome! Just yesterday, I went through my collection, and just threw them into a bin, with hopes of sorting them, someday. It’s like you read my mind! Off to the garage…

  5. I use shrink tubing as well, but I write a tiny label on the tubing with a fine-point pen before shrinking, which is easy to do since the tube shrinks 2:1. The result after shrinking is even tinier crisp black writing that is still very easy to read. I use yellow tubing for the best contrast, but I suppose you could still color code some tools. Plus I use this method for ALL tools, including drills bits. A quick dusting of Krylon Crystal Clear acrylic makes the label smudge proof.

  6. Bit Workshop Thanks for chiming in. I hear ya, and I don’t disagree about using good tools. Some of the freebie L-wrenches are soft garbage. I own a few T-handles and hex-drivers in larger sizes. But in my experience, the smaller sizes of the good brands are still prone to premature wear…or maybe I just lack finesse when using them. When I was working on space tools, we had to swap out our smallest Bondhus T-handles fairly regularly. And don’t get me started on ball-end hex drives!

  7. I see that my shot in the dark found its intended target! I reject your intuitive and organized system of measurement and cling to my own…because ‘Murica.

    Thanks for being a good sport.

  8. I am a graphic designer when I’m not preoccupied with making random stuff. I had a toolbox drawer full of good quality, but entirely random allen wrenches, including some that I’d cut the short leg off to make hex drivers that would fit in my cordless drill. It was, generously put, a freaking mess. I got fed up with playing allen wrench roulette, so one rainy day I sorted and sized them using a nifty little tool I got online that is like one of those cards for sizing drill bits. I put them in baggies and labeled the sizes. The nice thing about the sizing tool is that it let me differentiate (mostly) between SAE and metric wrenches. A few days later I worked out a trade with one of my clients that is a trophy shop with a laser engraver. They engraved each and every one with the size. I then rubbed some white paint in the engraving to make it show. I do like your color dabbing idea, though, for making the SAE and metrics easy to spot. Maybe I’ll dab one orange and the other safety green.

  9. I have, indeed, lived in the Big Easy and consider it my second “home town” after Nashville. I’ve been called N’awlins Chris once or twice over the years, but I am relatively certain that you have mistaken me for someone else. I don’t think we’ve ever met, although, I can’t be sure about that.. there are a few years in the early eighties that are a bit fuzzy. Nevertheless, HELLO!

  10. Moore Dude, mike Dawson here…we met at Brady’s studio..I was his first paying client..But if you’re not that Moore, a pleasure to meet another maker…peace…

  11. Terry, I don’t know where all your hex wrenches came from, but my dozens of metric and SAE wrenches are all marked by size. Usually it’s marked on the long arm of the L-shape wrench, on the side away from the direction that the short arm points (hope that makes sense). For what it’s worth, Allen is owned by the Apex Tools group, and still make hex wrenches.

    The cased sets have the size next to the hole that the wrench goes in; that’s not always foolproof (goodness knows I’ve been making a fool of myself for years), but it’s a help. You can get empty cases from Bondhus and other folks.

    Biggest hint I’ve got for working with hex socket fasteners: clean the crud out of the socket before you try to put the wrench in. If there’s crud, the wrench doesn’t go all the way to the bottom, and it’s way easier to strip either the tool or the fastener.

    Thanks for the hint, though; I’m going to use the color coding idea on some other things. Why buy when you can make it?!

Leave a Reply

Your email address will not be published.

Tested: SLR Magic Cine Lenses for Micro Four Thirds Cameras!

Tech

Tested: SLR Magic Cine Lenses for Micro Four Third…

Joey continues his journey testing cine lenses with this set…

Adam’s One Day Builds: Razor Crest Mods, Part 1!

One Day Builds

Adam’s One Day Builds: Razor Crest Mods, Part 1!

Adam and Norm begin the long-term project of modifying their…

Podcast - This Is Only a Test

Pop Culture Power Hour – This is Only a Test 650 –…

As we approach the debut of the Obi-Wan show, we discuss all the nuggets of Star Wars news revealed in the recent Vanity Fair feature. Kishore and Norm also react to the She-Hulk teaser, ponder Stan Lee's future in the MCU, and are wowed by two newly announced LEGO sets. Plus, some spoiler-light thoughts on the Picard season 2 finale and …

Inside Adam’s Cave: Wooden Screwdriver Mailbag Unboxing!

Show And Tell

Inside Adam’s Cave: Wooden Screwdriver Mailbag Unb…

Adam opens a viewer mailbag containing an ironwood interpret…

Ask Adam Savage: Behind the MythBusters Cement Truck Explosi…

Making

Ask Adam Savage: Behind the MythBusters Cement Tru…

In this livestream excerpt, Adam answers MythBusters-related…

Show and Tell: Adam Savage’s LEGO Minifigure Collection (Inc…

Show And Tell

Show and Tell: Adam Savage’s LEGO Minifigure Colle…

In this live stream excerpt, Adam shares his collection of c…

Ask Adam: Job Interview Advice, Jamie’s Flamethrower and Mor…

Culture

Ask Adam: Job Interview Advice, Jamie’s Flamethrow…

In this live-stream excerpt Adam answers questions from Test…

Let’s Build: Japanese Steamed Bun Shop Kit!

Making

Let’s Build: Japanese Steamed Bun Shop Kit!

This cozy miniature representation of a Japanese steamed bun…

Ask Adam: The Origin of M5, M6 and M7 (Plus, Their Neighbors…

Culture

Ask Adam: The Origin of M5, M6 and M7 (Plus, Their…

Adam answers questions from Tested members Aaron and Silver …

Podcast - This Is Only a Test

Ctrl-F For Real Life – This is Only a Test 649 – 5…

On the night after Google I/O, Kishore and Norm pod up to discuss the new Pixel devices announced and teased, and break down the augmented reality demos shown. We also share thoughts on the Moon Knight finale (spoilers within!) and compare notes on the technology of the Avatar 2 teaser. Plus, the end of the iPod era!